Carbon monoxide is a poisonous gas. This gas is found in any Glendale heating system. It can be deadly if you inhale it. That’s why there are carbon monoxide detectors in place to detect it right away. For this gas to make its way to your Glendale home is through a leak in your heating system. Thankfully, there are ways to prevent it from happening.
What are the Ways to Prevent Leaks in Your Heating System in Glendale?
There are regular maintenance procedures that you can do on your own. However, you still need to hire an HVAC contractor to perform yearly maintenance on your heating system. A contractor is highly trained to ensure proper cleaning of the furnace. The technician will also check the system for any cracks and leaks.
If the technician finds leaks, a repair must be done immediately. Don’t use your heating system without first addressing the leaks. You should also not attempt to repair the leaks yourself.
Install Detectors in Your Home
There are different models of carbon monoxide detectors available on the market. However, you should consider getting a model that can detect even the smallest trace of gas leaks. And when you install it, consider installing a few around your house and not just in one place. The ideal places are near your bedrooms.
Replace Filter Regularly
Carbon monoxide leaks can arise if there’s a backup of airflow in the heating system. This can be easily prevented by changing the air filter regularly. How often you need to change it will depend on how you use the furnace throughout the heating season. It can be every few weeks. You may check the instructions of your heating unit’s manufacturer. Replacing the filter is necessary to prevent leaks and you can breathe easily.
Check the Installation
In some cases, the leaks are the result of incorrect insulation of the heating system. If the blower motor wasn’t installed properly, problems could arise and one of them is venting carbon monoxide. For that reason, it’s always ideal to have the heating system installed by a qualified professional. In that way, the installation is done properly and you won’t face any issues with the system later on.
Avoid Vent-Free Gas Fireplaces
Venting carbon monoxide out of your home may be necessary so that none of the gas enters your living space. It’s necessary to have exhaust so that the poisonous fumes that the fuel burned would be released to the outdoors. But this isn’t possible if you choose a ventless gas fireplace. If your home has a vent-free heating system, make sure to replace it right away.
Take the Necessary Steps
You can protect your Glendale home from carbon monoxide leaks by ensuring that the heating system is working properly. To avoid carbon monoxide leaks from your Glendale heating system, make sure to follow the tips above. Or schedule an HVAC contractor for repair or yearly maintenance: (818) 722-8634.
If you are having trouble with your heater, your first instinct might be to find professional heater repair in Glendale. This is definitely the best call most of the time, but here are a few ways to figure out what’s wrong with your unit beforehand.
Problems with the Furnace Filter
Before anything else, the best thing to check is the filters in your heater. After all, these get dirty due to the constant intake of dust and dirt, quickly interrupting the airflow and clogging up the filter. In the best of cases, clogged filters decrease the air quality of the room in question. In the worst, well, your heater will stop working. It can keep the heater from starting up in the first place, as well as cause premature breakdowns and become a fire hazard. In order to check whether or not the filter is the problem, turn the thermostat off and flip the heater switch off. Hold up the filter to a light source. If the light doesn’t really shine through, then the filter definitely needs to be cleaned or replaced. Do this every month to make sure your air is clean.
Problems with the Thermostat
If the filter is changed and the heater still won’t run, then the problem might be with the thermostat. To check whether this is the case or not, set it to heat and set the temperature at least five degrees above the current room temperature. Replace the batteries if that’s the problem with the thermostat. For electromechanical thermostats, then you might need to open it up and dust it off using a soft brush to remove dirt from the metal coils and contact plates. Lastly, make sure that the thermostat itself isn’t being affected by external sources. Lights, ovens, and sunlight can all cause false readings. This can cause it to stop heating before it should or to not reach the necessary temperatures.
Problems with the Switch and Panel
If the problem doesn’t seem to be caused by either the filter or the thermostat, then power might be the problem. If you think this might be the issue, check the furnace switch near the furnace, for someone might have accidentally turned it off at some point. In these cases, flip it back on. If that doesn’t work, check the electrical panel and make sure that power is turned on at the breaker box. If the heater breaker is switched off, flip the switch all the way off, then flip it back on again so that you hear a click. If there’s no power coming to the fuse box, look for the melted fuse, unscrew it, and replace it with a fuse of the same type and size. Then, turn the heater back on and see if power was restored to it. If this isn’t working, then you might need to contact professional heater repair in Glendale.
Heater Repair in Glendale
At American Cool and Heat, we specialize in repairing any malfunctioning of heating and air conditioning equipment all across Glendale and the general Los Angeles area. We take pride in delivering only the best available services, guaranteeing optimal performance. For heater repair in Glendale and other services, give us a call at (818) 722-8634 if you find yourself in need of a repair and we’ll be right there.